搜索资源列表
newJLQ
- PIC 16F877A 直流电机PWM调速 -The PIC 16F877A DC Motor PWM Speed
DC_blashless_motor_control
- 无刷直流电动机调速控制程序.程序为ASM，配合书本 电机控制的DSP实现-Brushless DC motor speed control program. Program for ASM, with books and motor control DSP implementation
ADMC_401-SVPWM
- 基于ADMC_401的三相交流感应电机的SVPWM变频调速研究，通过对感应电动机的矢量控制原理分析, 提出了一种PID神经元网络控制器-SVPWM variable frequency speed control studies based ADMC_401 three-phase AC induction motor, induction motor vector control principle analysis, proposed a PID neural network control
STM32-motorControl
- 基于STM32微控制器的交流电机变频调速试验系统，对交流电机进行控制-Test system based STM32 microcontroller AC Motor, AC motor control
dsPIC30F4011
- 基于dsPIC30F4011的交流感应电机变频调速控制器设计，针对节能降耗的目的，开发了一套具有变频调速的电机控制系统。该系统通过工控机、电位器和外部专用仪表，对电机控 制芯片dsPIC30F4011的MCPWM模块调制出的三相正弦波的频率进行设定和改变，来实现变频调速控制，达到了预期的 控制效果-Based on the dsPIC30F4011 the AC induction motor variable frequency speed controller design for
pidaicheng
- 设计单片机系统拟实现电子调速皮带秤。本系统利用称重传感器测量输送带有效称量段上物料的重量，并将被测重力转换成相应的模拟电压信号，经放大器放大后，由A/D转换成数字量。与此同时，速度传感器将皮带速度转换为计数脉冲后进行整形。2路信号都送到C8051F410中进行计算、处理，得到当前皮带秤的瞬时流量值，对瞬时流量进行积分得到一段时间内的累积重量。瞬时流量与给定流量进行计较，运用PID算法，输出控制信号控制变频器来改变电机转速，从而可以实现流量的闭环控制。此部分需要设计2路信号输入通道，分别为称重传感
DC-MOTOR-PIDbihuan
- 基于51单片机的直流电机闭环PID调速系统的设计-Based on 51 single-chip closed-loop PID DC motor speed control system design
PID-BIHUAN-MOTOR
- 基于51单片机的直流电机闭环PID调速的设计与控制系统课程设计-Curriculum design and control system based on 51 single-chip closed-loop PID speed control of DC motor
stepmotor
- 单片机控制步进电机两相四拍工作方式，及调速程序-Chip stepper motor control two-phase four ways of working, and the governor procedures
DC-motor
- 单片机控制直流电机定时正反转，及调速程序-SCM control the DC motor timing reversing and speed control program
infineon_60dgree_hall_PWM_ok
- 用英飞凌8位单片机实现60度hall的无刷直流电机的运行，完整版可改变占空比调速。-Brushless DC motor running 60 degrees hall Infineon 8-bit microcontroller, the full version can change the duty cycle governor.
zhinengche
- 通过初始化程序对智能车实现PWM调速，并通过对传感器采集的信号进行处理使伺服电机左右摆角自如。-PWM speed smart car through the initialization process, and collected by the sensor signal processing swing angle around the servo motor freely.
1
- DSP电机控制的一个实验，可实现调速和方向的改变。-Experiment DSP motor control, speed control and direction of the change can be achieved.
PWM-OK
- 直流电机PWM调速C语言编程，配合PL51开发板使用。-DC Motor PWM Speed C programming language, with the the PL51 development board.
bujindianji
- 通过C51单片机编写程序，实现对步进电机的控制及调速功能-C51 microcontroller programming, stepper motor control and speed control functions
DCmotor
- 用DSP控制直流电机的转速并且可以无极调速-DSP controlled DC motor speed and stepless speed control
DLeeY20110120zz
- 双转子电机开环调速程序，转矩转速控制系统-Dual-rotor motor open loop speed control procedures, torque and speed control system
Brushless-motor--Program
- 无刷直流电动机调速控制程序，使用汇编语言，控制三相无刷电机的启动停止运行。-Brushless dc motor speed regulation control procedures, the use of assembly language, control three phase brushless motor start stop running.
stepmotor
- 基于51单片机的步进电机的控制与调速（课程设计）-Based on 51 single-chip stepper motor control and speed control (course design)
PMSM_Slidingmode
- 永磁同步电机基于滑模观测器的调速系统仿真研究-PMSM control system based on smo